Summary

In short: A COA is only useful when it can be tied to a specific grade, batch and test method. Review identity, the specification reference, method and limits, batch identifiers and the companion TDS / MSDS / specification sheet together. Any value that cannot be traced back to an actual document should be treated as unconfirmed.

Why the COA is the centre of the review

For a botanical extract, the certificate of analysis is the document that connects a delivered batch to a set of measured results. It is not a marketing summary. A useful review starts by checking that the document describes the same grade, the same specification and the same batch that you intend to buy.

Where a supplier publishes indicative values on a website, treat them as orientation only. The confirmed values are the ones on the document issued for the material under evaluation. This is why we keep specification figures off our product pages and point buyers towards the actual COA and TDS instead.

Check identity, grade and specification reference

Begin with the basics: ingredient name, botanical source information, grade or specification code, extraction ratio or marker definition, and the batch or lot identifier. If any of these are missing or inconsistent with the specification sheet, the rest of the document is difficult to interpret.

  • Ingredient name and grade match the quotation and the specification sheet.
  • A batch or lot identifier is present and can be linked to traceability records.
  • The extraction ratio, solvent or active marker definition is stated or referenced.
  • The document version or issue date is identifiable.

Methods, limits and the companion documents

A result without a method is hard to compare. Look for the test method category, the reference standard or pharmacopoeia where applicable, and the acceptance limits used for the reported parameters. Heavy metal, pesticide residue and microbiological limits are usually reviewed together with the COA rather than in isolation.

Request the companion documents in the same pass: the TDS for handling and storage, the MSDS / SDS for safety, the specification sheet for the agreed parameter list, and the test method list where your quality system requires it. Our Documents We Provide section lists the categories that can be requested.

A short review checklist for your team

A consistent checklist shortens supplier qualification because it produces the same evidence set for every candidate. Keep it in your Supplier Quality Agreement or incoming-material procedure so the review is repeatable across ingredients and buyers.

  • Confirm the document belongs to the grade and batch being offered.
  • Confirm the parameter list matches the agreed specification sheet.
  • Confirm methods and limits are stated or referenced, not implied.
  • Confirm traceability, retained sample and change-control information is obtainable.
  • Record open questions and request the missing documents before commercial terms are agreed.

Frequently asked questions

Which documents can I request for a product?

Buyers can request a COA, TDS, MSDS / SDS and a specification sheet for a botanical extract, together with test methods, residue and microbiological limits, allergen information and retained-sample records where applicable. Every document is provided on request and is limited to what is actually available for that grade. Open the Documents We Provide table.

Is an MSDS / SDS available before I place an order?

Yes — MSDS / SDS documentation can be requested during supplier qualification rather than only at order stage, so EHS and QA review can happen before a purchase decision. Use the document request route and list MSDS / SDS together with any other files your review needs.

Which testing methods and standards are used?

Test method categories, pharmacopoeial references and third-party testing arrangements are stated in the COA and the agreed test method list for the grade, not as general claims on this site. No laboratory names or method claims are published before the supporting documentation is available. Review the Testing & Standards section.

View all FAQs

Sources and further reading

Internal references on this site:

Documentation sources: COA, TDS, MSDS / SDS, specification sheet and test method list — available on request and subject to the documents actually provided for the grade or batch.

No external study results, numeric limits or third-party laboratory names are quoted before the supporting documents are available.

Third-party sources

Third-party sources are listed here only when the underlying documentation and citation details are available.

Cited statements

Cited statements are added with their source and date once the source documents are available.

Statistics

No statistics are published before the supporting documents are available.

Reference sources, pharmacopoeial citations and internal SOP references are supplied with the actual documentation pack. No external study results or numeric limits are quoted here before source documents are available.